whats fuming
I was in another thread were they were discussing having problems fuming an implosion. What do they mean by fuming.
Thanks Bob |
Here's a video on gold fuming, you can also fume with silver. The gold has to be at least 22K and the silver has to be 99.9% pure.
http://technorati.com/videos/youtube...%3DTmQGSLT3JuQ |
Fuming is a process where you use a precious metal (usually gold -but can be others) and you introduce it into the flame between the torch head and the "object" you want "coated" or fumed. The heat in the flame causes the precious metal to boil off at molecular level from the source and will bond to the "object" further out in flame, there for "coating" the "target" object...
Its a technique to put gold plating on glass object without going through a electrolytical process..... Dale |
Fuming is awesome. here's a link to some pic's where all the colors in these pieces are from fume...http://www.lampworketc.com/forums/album.php?albumid=15.
I like to explain it as if it is like the process of evaporation. Think of it like when water turns to steam. well the metals turn to "steam"(fume) and travel up the flame...they stick to a piece of glass that you hold at tip of flame. You have a lot of research to do but you should definitely find everything you need to know on the internet. And theres plenty of peeps that will help answer questions here. |
thanks
Thanks every one. I'll watch the videos, Sounds like something to try.
Bob |
Just be very sure that you have outstanding ventilation when you fume things.
Robert |
Robert, what do you mean by outstanding ventilation? My workspace is 8 x 3 feet in my garage, next to the garage door. I usually work with the door open, will this suffice? I've been dying to try fuming, but am unsure of the ventilation issue.
Thanks so much!! Cricket |
Quote:
|
Thanks Carolyn...
Do I need to install a ventilation fan over my work area? Your advice is greatly appreciated!! Cricket |
Yes....
Robert once posted a pic of his work bench and vent hood. Looks like quite a thoughtful design. His picture is post #4 in the thread, below. Beth (GlassyEyedGirl) has the post just above. You can't see the fan in her picture, but she was kind enough to share some of her design info with me. She made sure she had an excellent fan with more than enough cfm for her vent hood design. What I like about both is that they are fully enclosed, fume hood type (aka barley box style) vent systems. I would recommend PMing them to find out more about what they did. Carolyn might have some good suggestions for you as well. http://www.lampworketc.com/forums/sh...37#post2301737 There are folks who also choose to wear a respirator, such as a 3M P100, when fuming for added protection, even with a vent system. Linda |
Cricket, you need something to draw the fumes away from you and make up air coming from behind you. I have a hood similar to Robert's, but smaller and not as pretty, and it is about two feet above my torch and of course venting to the outside. It has a kick ass fan in it because my DH used it to draw air out of the studio when he was turning wood bowls. I have an outside door open behind me for makeup air. I still use a respirator for enamels and fuming.
|
Okaaaay...
That equipment sounds like NEXT year's Christmas gifts!! Carolyn, Linda thanks so much for your input, I learn something new everytime I log on. Cricket |
Actually you can make something that will work for a lot less, in the meantime. You can buy flex duct from your local hardware store and a furnace booster fan. attach the booster fan to the end of the duct and place the other end in front of your torch or suspend it just above your work area. The fan will draw away the fumes and pull in air from behind you. Just make sure it is close but not too close to hinder your flame. The flex duct is easily suspended by hangers or even rope.
|
Quote:
Robert |
All times are GMT -7. The time now is 4:01am. |
Powered by vBulletin® Version 3.7.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.