Lampwork Etc. - Search Results

		Lampwork Etc. > Search Forums
Search Results

Showing results 1 to 9 of 9
Search took 2.21 seconds. Search: Posts Made By: CarolineM

Forum: Tips, Techniques, and Questions

2013-01-27, 4:19pm

Replies: 9

beads crack when using a masher

Views: 3,397

Posted By CarolineM

Yes, it turned out to be the bead release. Blue...

Yes, it turned out to be the bead release. Blue Coat in particular - so discouraging when ALL your beads break. I've been experimenting with Dip N Go Sludge with no problems at all. Thanks to all...

Forum: Tips, Techniques, and Questions

2013-01-09, 7:50pm

Replies: 9

beads crack when using a masher

Views: 3,397

Posted By CarolineM

I will try that. Lighter, quicker presses,...

I will try that. Lighter, quicker presses, rather than one full press. Thanks.

Forum: Tips, Techniques, and Questions

2013-01-09, 6:50pm

Replies: 9

beads crack when using a masher

Views: 3,397

Posted By CarolineM

I'll try to take/post a picture of them. Lyssa...

I'll try to take/post a picture of them.
Lyssa - I put the bead back into the flame immediately after mashing. And, yes even when its only mashed a little it still cracks.
Purple - The mandrel...

Forum: Tips, Techniques, and Questions

2013-01-09, 4:36pm

Replies: 9

beads crack when using a masher

Views: 3,397

Posted By CarolineM

beads crack when using a masher

I'm trying to learn how to use a masher to make 1/2 or 3/4" flat round beads and all of my beads have cracked. I've made about 15 so far. Could someone tell me what I'm doing wrong? I'm using a...

Forum: Safety

2012-01-15, 6:18pm

Replies: 4

Temperature of air in the ducts?

Views: 2,819

Posted By CarolineM

So, you have a booster fan and a 10" intake duct....

So, you have a booster fan and a 10" intake duct. I'll have another look at at my make-up air configuration. Thanks so much for your help. Its all starting to fall into place now.

Forum: Safety

2012-01-15, 12:21pm

Replies: 4

Temperature of air in the ducts?

Views: 2,819

Posted By CarolineM

So, I thought I was starting to understand a...

So, I thought I was starting to understand a little bit, but now the fog is returning. What is a vacuum plenum? And should I have put my fan under the table to blow in fresh air, rather than on the...

Forum: Safety

2012-01-15, 2:57am

Replies: 4

Temperature of air in the ducts?

Views: 2,819

Posted By CarolineM

Temperature of air in the ducts?

I haven't seen this addressed anywhere, and I've read loads of posts on this and other forums...
I'm new to beadmaking and am setting up my first indoor studio. I'm concerned about the temperature...

Forum: Tips, Techniques, and Questions

2011-09-05, 5:26pm

Replies: 0

Olympic kilns - 126 Lite, in particular

Views: 1,710

Posted By CarolineM

Olympic kilns - 126 Lite, in particular

Does anyone have any experience with Olympic kilns? I'm looking at the 126 Lite with bead door, from Kilnfrog, but I haven't seen any mention of it on any forums. I like the dimensions because it...

Forum: Torch Questions

2010-05-24, 11:14am

Replies: 13

Airsep NewLife Elite Service Manual Needed

Views: 17,094

Posted By CarolineM

Hi Alaska, Have you found the manual you need? ...

Hi Alaska,
Have you found the manual you need? I am thinking of buying the same model and was wondering about the LPMs. Have you found that it is enough? I will be using a Minor Bench Burner and...

Showing results 1 to 9 of 9

All times are GMT -7. The time now is 2:18am.