Lampwork Etc.
 
Send a PM to CorriDawn!

LE Live Chat

Enter Live Chat

No users in chat




Beads of Courage


 

Go Back   Lampwork Etc. > Library > Tips, Techniques, and Questions

Tips, Techniques, and Questions -- Technical questions or tips

Reply
 
Thread Tools
  #1  
Old 2020-09-15, 2:52pm
blueaccord19 blueaccord19 is offline
Junior Member
 
Join Date: Sep 15, 2020
Posts: 1
Default Chili pepper kiln not heating! Help!

So I'm right in the middle of a few projects and of course my jen-ken chili pepper kiln decided to quit heating. I have heard it's the relays, so I ordered some relays. I'm an electrician by trade, so I put 12v to the relays and found that they change state with a meter. Then I get the LAG code which means the TC isn't heating up, so the contactor drops out and it drops power off of the element. So then I decided to put my heat gun inside the kiln and now as long as the TC is coming up in temp, I can measure 118v going to the heating element but the element never turns red after at least 5-10 min of waiting. So does that mean my heating element is bad? I will admit, I have a small torch (GTT Lynx) and I often use my kiln just to keep a piece evenly heated, so I constantly stop the kiln and refire it up to max temp to basically use as a heater since my torch doesn't supply a big enough flame and I constantly get pieces cracking and breaking. I have less than 100 firings with this kiln and just got it in february. I was going to call jen-ken today but they closed before I had a chance to call. Sorry if this has been addressed, but with a quick search I couldn't find this exact problem. Really need my kiln back! Thanks in advance for any help!
Reply With Quote
  #2  
Old 2020-09-15, 4:18pm
Eileen's Avatar
Eileen Eileen is offline
Loving learning
 
Join Date: Oct 11, 2010
Location: Florida
Posts: 11,444
Default

Call them in the morning, they are very helpful.

I can't answer your questions, as that is all out of my wheelhouse.
I have had to change the relays once, and the thermo couple once, but they helped me figure out what the issue was.

If you are turning it off and on in one session, why not leave it on? It doesn't pull that much electricity to keep it warm, vs heating from scratch over and over.
__________________
My current "hot" fantasy involves a senior discount on glass & tools!
Reply With Quote
  #3  
Old 2020-09-16, 3:17am
Speedslug's Avatar
Speedslug Speedslug is offline
Phill
 
Join Date: Mar 21, 2009
Location: Winnebago, MN
Posts: 2,227
Default

Sounds to me like it is either the element or the power source for it, which I think is going to be a Silicone Controlled Rectifier (SCR).

If you have done continuity testing of the element and it checked out good then is going to be the SCR.



But call the company.
They have a great reputation for troubleshooting over the phone.
Then you can get the part shipped at what ever speed you are willing to pay for and they will guide you through the installation steps if needed.

I have heard stories of total neophytes being guided through replacement of relay, elements and SCRs with great success.

As an electrician you will have no trouble at all.
__________________
Perpetually Pessimistic. I wish I was Pleasantly Surprised but I'm not surprised anymore.
Reply With Quote
Reply

Tags
jen-ken, kiln, not heating, problem


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump




All times are GMT -7. The time now is 5:59am.


Powered by vBulletin® Version 3.7.5
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Your IP: 54.237.183.249