|
Safety -- Make sure you are safe! |
2006-08-21, 4:45pm
|
Member
|
|
Join Date: Mar 21, 2006
Posts: 41
|
|
how do you look at your flame?
I have been off my torch for the summer and *tried* to make beads the other day and it was a mess from start to finish. I'm thinking of another thread for the more "technical" problems, and it occurs to me that this is maybe a health and comfort thing as much as anything, but figured I'd try here first to see if it gets any hits.
I have an adjustable chair, and as far as ergonomics go, I believe in moving as much as anything to alleviate problems. So I go up and down a lot on my little spinny chair. Usually. I could not seem to find anything resembling a comfortable position th other day. I even tried standing, but the strain of looking down was way too much for my neck to take. I usually try to angle my head (with minor wiggling to adjust the torch angle) so I'm looking slightly up at the bead, or dead across at it. I sometimes rest my elbows on the table on a gel wrist rest thing mostly shielded from flying glass by the edge of the stainless steel tray I work in/on. I'm waiting for the thing to ignite soon and send flaming goo everywhere (my life is like that), so usually I'm elbow to table top, not the best. This was jacking my shoulders higher than I remember before. So maybe try dropping my arms/elbows down, under the table level? I know people swear by the creation stations but I'd sort of like to try one before flinging a C-note into the mix. I have been using small propane tanks and want to switch to bulk tanks (more on that in the other thread), so adjusting how I look at the flame means adjusting how I attach the torch to the table more than before.
Oh, and I have ACE 202 glasses, that had been ok until the little hiatus, at least I thought so. Are they really AUR 92 glasses, or not? My eyes are a mess, 2 days later still all dry and gritty. I only spent about $30 on them, and they *said* they were AUR lenses, but everyone seems to spend a ton more on glasses so I'm rethinking the whole "just because it said so, doesn't make it necessarily so" thing.
So how do you hold you head and neck- and arms and elbows- when you torch??
thanks for the help-
Sarah
|
2006-08-21, 5:21pm
|
|
Satake Woman!
|
|
Join Date: Jun 05, 2005
Location: South Carolina
Posts: 4,949
|
|
Sarah, where are you at? It would be best if you could find someone near you to try out their creation station. I find that mine has done my back a world of good.
__________________
Jo
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Satake glass in stock and ready for you!
|
2006-08-21, 5:53pm
|
Member
|
|
Join Date: Mar 21, 2006
Posts: 41
|
|
I'm in Lexington, KY, Jo. I've only heard raves about the creation station, but never used one. Will the elbow rests move vertically?
Ok, I'm glad you told me that, Kimberly. I looked at the auction, it said AUR 92 in the description, but ACE 202 on the box. Shafted. I hate that. I got them months ago when I was compiling supplies to get started. It was from glass vendors people liked :shrug:
But how do you position yourself at the torch???
thanks-
Sarah
|
2006-08-21, 6:33pm
|
|
Satake Woman!
|
|
Join Date: Jun 05, 2005
Location: South Carolina
Posts: 4,949
|
|
Sarah, they don't move vertically but you can put leather pads on them to raise your elbows if you like.
__________________
Jo
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Satake glass in stock and ready for you!
|
2006-08-21, 7:47pm
|
|
Safety ALWAYS
|
|
Join Date: Jun 10, 2005
Location: Sauk Rapids, Minnesota
Posts: 2,401
|
|
ACE 202 filters are made by Phillips. The problem is probably optical quality, probably NOT filter quality, unless the lenses are very thin.
If you are working soft glass, any of the ACE filters (we call them AUR-92) are fine. If you are working borosilicate, you should NOT be working with just ACE filters, you need additional filtration to block the IR.
Your symptoms are very similar to overexposure to IR.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Chaotic Glass: Safety for the glassworker, and random thoughts and opinions on the state of the glassworking world To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2006-08-22, 9:04am
|
|
The Andrea Half
|
|
Join Date: Aug 18, 2006
Location: Georgia
Posts: 1,411
|
|
What are good lampworking glasses to use when you already wear prescription glasses? I don't do boro work; just Moretti / Lauscha / Vetrifond on a HH.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. * To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. *
|
2006-08-22, 10:12am
|
|
Senior Member
|
|
Join Date: Feb 15, 2006
Location: In my Studio
Posts: 1,811
|
|
Mincot , use the clip ons that Mike A. has for lampworking.
Janet
|
2006-08-22, 7:53pm
|
|
Glass Jack in the Box
|
|
Join Date: Aug 01, 2006
Location: Central IL
Posts: 116
|
|
Can also look into bench shields the Mike also has, under "other filter products".
There are two kinds, one for softglass and one for boro.
PondRacer
__________________
Rubber toasters and square eggs. Ain't life grand?
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 6:12am.
|