|
Tips, Techniques, and Questions -- Technical questions or tips |
2010-01-04, 12:31pm
|
|
Annie
|
|
Join Date: Jan 04, 2010
Location: Kaufman, TX
Posts: 96
|
|
Converting a ceramic 220V kiln to a bead annealer
I have an old 220V octagon top lid ceramic kiln, and I am wondering if I can use this for lampwork annealing? It does not currently have a digital controller.
|
2010-01-04, 12:40pm
|
Senior Member
|
|
Join Date: Feb 06, 2009
Posts: 501
|
|
yes, you can. A kiln is a kiln is a kiln. It doesn't even have to have a digital controller, but that makes it simpler. You can buy controllers separately from kilns. Personally, I'd probably use a top loader for batch annealing.
|
2010-01-04, 1:06pm
|
|
Senior Member
|
|
Join Date: Dec 11, 2006
Location: TX
Posts: 586
|
|
I also have an old 220v octagon kiln sitting in my garage and was wondering how to convert it over to 110v. Any idea where to go to find the information on how to switch it?
-Elaine
|
2010-01-04, 1:14pm
|
|
Senior Member
|
|
Join Date: May 04, 2007
Location: San Jose, CA
Posts: 1,212
|
|
Quote:
Originally Posted by missbatteries
I also have an old 220v octagon kiln sitting in my garage and was wondering how to convert it over to 110v. Any idea where to go to find the information on how to switch it?
-Elaine
|
Short answer: you can't.
Long answer: While you might be able to compute the new size and length of elements needed to run the kiln on 110 volts, and replace the elements, the kiln would then either draw more current than is available through a typical 110 volt circuit, or would take forever to heat up.
Malcolm
__________________
ARTCO
Artist's Reliable Tool Company
Website: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Email: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Phone:+1.408.288.7978
|
2010-01-04, 1:28pm
|
|
Senior Member
|
|
Join Date: Dec 11, 2006
Location: TX
Posts: 586
|
|
Bummer.....thanks Malcolm.
|
2010-01-04, 4:19pm
|
Senior Member
|
|
Join Date: Feb 06, 2009
Posts: 501
|
|
getting an electrician to set up a 220 outlet isn't impossible, though, and in my experience is far less expensive than buying another kiln....
|
2010-01-04, 7:06pm
|
Alaska Boro
|
|
Join Date: Dec 10, 2009
Location: Anchorage, Alaska
Posts: 1,065
|
|
Kiln Wiring
The best way to find out is to use an Ohm meter to check the resistance of one element. On my homemade annealer the element measures 11.8 ohms. At 117 V AC this comes out to 9.9 amps or 1160 watts. It takes 57 minutes to heat up to 1050 F.
Note: since elements are low resistance be sure to substrate the resistance of your meter leads. Perhaps .2 ohms depending.
If the elements are in the range of 10 to 8 ohms you could use one element connected up to a single 117 V AC power source. Two could not be used as the overall current would be around 20 amps which would trip the standard household circuit.
The other issues are the volume of the kiln and heat loss. 1100 to 1700 watts may be sufficient again depending.
|
2010-01-04, 11:09pm
|
Kobuki & DIY Homefill Sys
|
|
Join Date: Apr 30, 2009
Location: socal
Posts: 220
|
|
Quote:
Originally Posted by likes to make glass stuff
getting an electrician to set up a 220 outlet isn't impossible, though, and in my experience is far less expensive than buying another kiln....
|
i agree. most homes have 2 hots and a neutral coming in to the main breaker box. Standard 120 uses one hot and one neutral and ground. 220 uses the two hots and ground. So it should be very easy and fairly cheap to get an electrician to set up a 220 outlet at almost any home connected to the grid.
Personally, I'd rather set up a new 220 line than swap out elements and relays to convert a 220v kiln to 120v.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 11:37am.
|