|
Tips, Techniques, and Questions -- Technical questions or tips |
2018-02-12, 6:57am
|
Junior Member
|
|
Join Date: Aug 11, 2008
Posts: 19
|
|
Losing Propane
Went to use my torch and had no propane at all. Hadn’t torched for a week, and the tank was recently new. My husband changed the tank, watched the regulator, and noticed that there was a decline in the propane. Assuming there is a slow leak in the hoses which are about ten years old. Until we can get new hoses, is it okay to use my torch? Appears it is a very slow leak. Any help is appreciated. I need to make beads today, while he is trying to locate new hoses. Thanks for any help. I am on a mini cc with an oxygen concentrator from extreme oxygen, ex-20.
|
2018-02-12, 7:26am
|
|
Senior Member
|
|
Join Date: Jun 23, 2005
Location: Up and down I-95
Posts: 4,390
|
|
No! Too dangerous. BTW- regulators and flashback arrestors wear out as well. If you haven't changed anything in 10 years, it may be time. I've replaced everything 3 times in the same amount of time.
__________________
Rebecca
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2018-02-12, 7:44am
|
|
Senior Member
|
|
Join Date: Aug 31, 2006
Location: Knoxville, TN
Posts: 2,215
|
|
Oh no! Do not torch. You are aware that propane pools in low spots, right? It does not dissipate. Is it inside? Either way, you need to use some fans to blow it away from wherever it may have settled. I hope your tank is outside, but it will also explode there, so corrective action is needed.
__________________
Kathy
|
2018-02-12, 4:54pm
|
Senior Member
|
|
Join Date: May 27, 2008
Location: Albion NY
Posts: 517
|
|
it may be a loose fitting, a mix of 15 parts water to 1 part dish soap may help find the leak.
Or you maybe able to hear what's hissing.
At the very least it will identify the part that needs replacing.
Turning the propane off at the tank should be standard practice.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2018-02-13, 1:48am
|
|
Slogan Challenged...
|
|
Join Date: Mar 21, 2009
Location: Maricopa, Arizona
Posts: 6,287
|
|
well that doesn't sound good. I would check your regulator for sure. Unless your torch is leaking, and that can happen too. if your hoses are that old, it is an obvious thing to replace them. But I would check to make sure you know where the leak is. Stay safe and hope you can get back to melting soon.
__________________
Kristin ~
Facebook: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Etsy: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2018-02-13, 12:11pm
|
|
hyperT
|
|
Join Date: Jan 31, 2013
Location: San Antonio, Texas
Posts: 582
|
|
Leaks
Mix up some soapy water and spray it on to the hoses etc to find the leak.
You will get bubbles where the leak is.
Have fun, Wayne
|
2018-02-14, 1:45am
|
|
Phill
|
|
Join Date: Mar 21, 2009
Location: Winnebago, MN
Posts: 2,489
|
|
Oh and for propane make sure you are using "T" rated hose.
It should be marked on the hose and they are typically black like bar-b-que hoses.
The red and green hoses for acetylene can disintegrate from the inside because the propane chemically destroys the hose.
And all hoses can break down down from sun light and weathering and just from getting old.
I think need to be replaced every dozen years or so.
__________________
The Zombie Apocalypse is Upon Us.
|
2018-02-14, 10:32am
|
|
Senior Member
|
|
Join Date: Aug 31, 2006
Location: Knoxville, TN
Posts: 2,215
|
|
My T grade hose is red
__________________
Kathy
|
2018-02-14, 8:56pm
|
|
Phill
|
|
Join Date: Mar 21, 2009
Location: Winnebago, MN
Posts: 2,489
|
|
Thanks Kathy.
I didn't know it came in red.
It has be a decade or more since I followed the details so I am out of touch, again.
__________________
The Zombie Apocalypse is Upon Us.
|
2018-02-16, 12:09pm
|
|
Senior Member
|
|
Join Date: Jul 11, 2005
Location: Mesa, AZ
Posts: 1,588
|
|
Ok, so how do I know if my torch itself is leaking? Just process of elimination? I hate to spend the money on a new torch if that isn't it. Is it possible the typical propane smell is a product of the fuel burning off? I don't smell anything when my torch/propane isn't on. Will the soapy water also work to test the arrestors and quick connects? My dials on my regulator are steady. Does that mean it isn't my regulator? I got all new hoses and I'm pretty sure I didn't smell anything when I first (recently) started using my torch again after years.
__________________
~Jeannie
|
2018-02-17, 12:17am
|
|
Slogan Challenged...
|
|
Join Date: Mar 21, 2009
Location: Maricopa, Arizona
Posts: 6,287
|
|
if the torch is leaking, you can smell propane around the valves. Sometimes they leak but you can just replace them.
Soapy water for all the connects. Some say that Dawn corrodes brass and there are some things online you can buy to check those connections. I haven't tried any, yet anyway
__________________
Kristin ~
Facebook: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Etsy: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2018-02-17, 12:43pm
|
|
Senior Member
|
|
Join Date: Jul 11, 2005
Location: Mesa, AZ
Posts: 1,588
|
|
Today's project: Testing all the connections and lines. I have a very diluted solution of Palmolive.
__________________
~Jeannie
|
2018-02-17, 1:30pm
|
|
Senior Member
|
|
Join Date: Jul 11, 2005
Location: Mesa, AZ
Posts: 1,588
|
|
Quote:
Originally Posted by Beadazoid
Today's project: Testing all the connections and lines. I have a very diluted solution of Palmolive.
|
OK! Mission accomplished!! Parts tested, leak found, part replaced! It was the non-torch half of the quick-connect. I happened to have an extra one here! Now all that's left is to re-verify once I start up my torch (later today).
__________________
~Jeannie
|
2018-02-17, 2:01pm
|
Member
|
|
Join Date: Oct 24, 2013
Posts: 80
|
|
I'm using quick connects on my hoses to connect to my torch and have standard flashbacks on the regs. For finding leaks I will open the tanks and turn on the regs with everything hooked up ready to work. then I close the tanks down and watch the regs to see if they are dropping. If one is then I will disconnect the torch with the quick connect, no worries they have check valves, and watch to see if the reg is still dropping. Hopefully it is as I would rather replace the hose, quick connects, or regulators than torch valves.
I have Y splitters on my hose lines to run my main torch and the hand torch with quick connects on the splitters. This is my second stage to check. I'll open the tank and close it again to fill the next section for checking. Soapy water in a spray bottle is best for checking.
Make sure to check around all the connections on the regs also.
Good luck.
|
2018-02-18, 12:40pm
|
|
Senior Member
|
|
Join Date: Jul 11, 2005
Location: Mesa, AZ
Posts: 1,588
|
|
Quote:
Originally Posted by Beadazoid
OK! Mission accomplished!! Parts tested, leak found, part replaced! It was the non-torch half of the quick-connect. I happened to have an extra one here! Now all that's left is to re-verify once I start up my torch (later today).
|
Nope. That apparently was not the only one. After I replaced the quick connect part I retested all the connects and regulator again and found another leak on half of the flashback arrestor. I'm going to see if that will tighten enough if I use 2 wrenches. I hope so or I'll have to buy another.
So test and retest.
__________________
~Jeannie
|
2018-02-18, 4:24pm
|
Senior Member
|
|
Join Date: May 27, 2008
Location: Albion NY
Posts: 517
|
|
For the peanut gallery
If there is an issue with the torch your local welding supply or the manufacture maybe able to clean the metal pieces and replace the O rings and needle valves.
The flash back arrestors are at least something you can address and replace locally being a common universal part.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2018-02-18, 5:09pm
|
|
Phill
|
|
Join Date: Mar 21, 2009
Location: Winnebago, MN
Posts: 2,489
|
|
Another thought from one who has learned the hard way;
These brass fittings at designed with soft metal and if a person cranks down on them too hard they can ruin the sealing surfaces and wind up needing to get them re-ground.
Also if the torch valves are hand closed really hard the stem can get bent and that will entail sending it back to the manufacturer to get repaired.
With these precision surfaces the amount of pressure needed to seat the parts gas tight really isn't much more then what is needed to to push the blood out of your skin to a lighter color as you close the parts together.
Seems there is a way that metal to metal contact can actually weld the two parts together and when they are opened again chunks from one surface will get torn out because it is bonded with the other. I think the metal guys call it galling.
I remember that there was an issue with that happening on one of the first space flights when the astronaut (or it could have been a cosmonaut) could not get the hatch closed because of it.
ETA: It's called cold welding and here is a youtube video on the subject;
https://www.youtube.com/watch?v=A8FgA7Narfs
__________________
The Zombie Apocalypse is Upon Us.
|
2018-02-19, 5:29pm
|
|
Senior Member
|
|
Join Date: Feb 21, 2017
Posts: 422
|
|
Do you not close the propane tank after torching, and burn the fuel out of the lines after? I mean, it's also good to check and fix leaks, but doing those steps may help extend the lifespan of your equipment.
__________________
My To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 8:23pm.
|