|
Safety -- Make sure you are safe! |
2011-07-23, 8:13pm
|
|
Senior Member
|
|
Join Date: Aug 31, 2008
Posts: 187
|
|
Are there guidelines for distance from torch to back wall?
I am currently using a Nortel Minor torch, but this fall we plan to renovate the "glass studio" and I am upgrading to a GTT scorpion. I can find lots of advice about ventilation systems, but I have not seen any guidelines for how much space needs to be between the torch face and the back wall. I assume it varies for various sized torches and possibly whether you have a metal sheet with air space between it and non flamable cement board. If this has been covered before, can anyone point me in the right direction? Thank-you in advance.
Darrell
|
2011-07-24, 8:29am
|
|
Gentleman of Leisure
|
|
Join Date: Jun 10, 2005
Location: A Little Bit West of Yosemite Valley
Posts: 5,200
|
|
Basically its sort of after torch is in operation for a while, and you can place hand on wall behind torch and is may be slightly warm (not uncomfortably hot) you are pretty safe... Usually 12 to 18 inches.... So if you have a minimum depth of bench of say 24 inches, and torch is at front edge of bench you should be pretty good....Obviously further torch is away from wall the better... But distance may not always be practical... It does not hurt to have nonflammable backing like metal or cement board with small air space for convection to carry any heat away that may penetrate through "heat shield"...
Dale
__________________
You can lead a person to knowledge, but you can't make them think. To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
Vendor-Artist-Studio-Teacher Registry To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
San Francisco - A Few Toys Short of a Happy Meal
|
2011-07-24, 10:48am
|
|
Curmudgeon Engineering
|
|
Join Date: Feb 15, 2006
Location: Near Seattle, WA
Posts: 1,723
|
|
If the wall catches on fire your torch is too close!
LOL
What Dale said actually!
|
2011-07-24, 10:56am
|
|
Senior Member
|
|
Join Date: Aug 31, 2008
Posts: 187
|
|
Thank-you Dale. I appreciate all you safety posts here on LE. The renovation will probably have a built in counter as opposed to a movable table, so if it isn't wide enough, to won't be easy to change it. I was worried that I might need three feet or more, which would cut into room space.
Darrell
|
2011-07-24, 10:56am
|
|
Curmudgeon Engineering
|
|
Join Date: Feb 15, 2006
Location: Near Seattle, WA
Posts: 1,723
|
|
Thought I might add some comments/observations here to offset my facetious remark above.
Most people operate their torch at a 45 degree or so angle upward. Work benches are usually (always) 24" or more deep. People with these shallow benches usually put something like hardiboard on the wall. Sheet metal spaced a half inch from the wall is also excellent. If the ventilation is adequate the hot gasses are drawn up and out fast enough that the wall remains relatively cool. It will get warm but no where near combustion temps. If your bench is shallow then you might look at making a torch extension on your table to move the torch further away from the wall; sort of like a diving board or porch where your torch is mounted. This platform can be made to swing out of the way if space is critical.
HTH, PJH
|
2011-07-24, 3:50pm
|
|
Senior Member
|
|
Join Date: Aug 31, 2008
Posts: 187
|
|
Thank-you for the comments. I didn't find your remark facetious.
Darrell
|
2011-07-27, 5:52am
|
|
Unmedicated since '62
|
|
Join Date: Jan 18, 2009
Location: Hunter Valley, Australia
Posts: 5,907
|
|
I have posters on the wall in front of my torch - I figure if they're not catching fire then I'm fine
I think heat actually rises pretty fast
__________________
Deb
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. - my 17yo sons first novel
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. - download, get organised, enjoy
|
2011-07-27, 7:45am
|
|
Senior Member
|
|
Join Date: Feb 05, 2011
Location: Upstate NY
Posts: 144
|
|
Maybe we can make a new rule? I'll guess at 3X the length of the flame. Anybody?
__________________
Conrad
Knight Bullet Burner
Tanks
mostly boro technical projects
"I'm sure I'm on a planet but I don't know if it's still earth."
|
2011-07-28, 3:46am
|
|
Unmedicated since '62
|
|
Join Date: Jan 18, 2009
Location: Hunter Valley, Australia
Posts: 5,907
|
|
Quote:
Originally Posted by Conrad Hoffman
Maybe we can make a new rule? I'll guess at 3X the length of the flame. Anybody?
|
I reckon the rule should be that you have to be able to hold your hand on the wall in front of the torch indefinitely
__________________
Deb
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. - my 17yo sons first novel
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. - download, get organised, enjoy
|
2011-07-28, 11:11am
|
|
Curmudgeon Engineering
|
|
Join Date: Feb 15, 2006
Location: Near Seattle, WA
Posts: 1,723
|
|
If you can hold your hand on something for 10 seconds but not more (give or take a few) the object is about 165 degF. That is a 'rule' we used onboad ship for checking bearings.
|
2011-07-28, 5:18pm
|
|
Senior Member
|
|
Join Date: Feb 05, 2011
Location: Upstate NY
Posts: 144
|
|
Same rule works on dry land for transistor heat sinks.
__________________
Conrad
Knight Bullet Burner
Tanks
mostly boro technical projects
"I'm sure I'm on a planet but I don't know if it's still earth."
|
2011-07-28, 6:37pm
|
|
Senior Member
|
|
Join Date: Feb 09, 2006
Posts: 219
|
|
Quote:
Originally Posted by Conrad Hoffman
Maybe we can make a new rule? I'll guess at 3X the length of the flame. Anybody?
|
Sooo with say a PM2D the. Back wall would need to be ten feet away from the torch face? Sounds pretty unrealistic compared to having a piece of cement board with an air gap between it and the main wall....
__________________
AWESOME-SAUCE. The king of ban..........Proud member of "you people" of 9/13/11 - record post count, record view count.
|
2011-07-29, 10:22am
|
|
Curmudgeon Engineering
|
|
Join Date: Feb 15, 2006
Location: Near Seattle, WA
Posts: 1,723
|
|
If you are getting 3 ft of flame out of your PM2D you are working some serious glass and 10 ft may not be enough!!
I would have the fire department standing by LOL!
IIRC the radiant head lessens by the square of the distance; twice the distance 1/4 the heat but that does not take into consideration the effects of vent air flow and convection heat.
|
2011-07-29, 1:47pm
|
|
Senior Member
|
|
Join Date: Feb 09, 2006
Posts: 219
|
|
Quote:
Originally Posted by cheng076
If you are getting 3 ft of flame out of your PM2D you are working some serious glass and 10 ft may not be enough!!
I would have the fire department standing by LOL!
IIRC the radiant head lessens by the square of the distance; twice the distance 1/4 the heat but that does not take into consideration the effects of vent air flow and convection heat.
|
considering we melt 110mm tube and sometimes do melt ins on 14mm+ thick wall tube ues we do rage torches here. We also never have a 3 foot flame just going and nothing in it. When the torch is running that high its normally being soaked up by a piece of glass.
__________________
AWESOME-SAUCE. The king of ban..........Proud member of "you people" of 9/13/11 - record post count, record view count.
|
2011-07-30, 9:30am
|
|
Curmudgeon Engineering
|
|
Join Date: Feb 15, 2006
Location: Near Seattle, WA
Posts: 1,723
|
|
That sounds like a cool thing to watch. Serious glass indeed!
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 2:16pm.
|