|
2014-12-01, 11:02pm
|
|
Member
|
|
Join Date: Nov 09, 2011
Location: Fallon, Nevada
Posts: 84
|
|
Recipe for Electroforming (Copper)
Hi All!
As I have wanted to give back for all of the knowledge that I have accumulated from you very generous lampworkers, I am sharing this recipe for an electroforming solution so that you can electroform (copper coat thicker than plating) your beads or whatever objects that you desire.
Compared to purchasing an electroforming solution, this is really cheap.
What you will need: (This makes 3 gallons, so if you need less, break it down accordingly)
1. A blue plastic water jug...at least 3 gallons, preferably 5 gallons
2. Large funnel
3. 3 gallons distilled water
4. 2.5 pounds of copper sulfate crystals (check hardware or swimming pool supply stores)
5. 1 pint sulfuric acid (most auto parts stores, such as Napa, have this and call it simply battery acid)
6. "New Copper Brightener Part B" ( www.caswellplating.com the only thing you will have to order for the solution)
The big thing to remember is "DO WHAT YOU OUGHTER, ADD ACID TO WATER". Remember this little ditty when you are making up the solution.
Mixing instructions: You might want to wear a mask and nitrile gloves to mix this. Safety first
1. Pour 2 1/2 gallons of the distilled water into the jug.
2. Start pouring in the copper sulfate crystals...use the funnel if you have to. Pour in part of the crystals (1/4 to 1/2) put the lid on the jug and agitate the ****out of it...shake rattle and roll. Pour in more crystals and do some more agitating. Do this until the crystals are no longer dissolving...that means the solution has reached maximum concentration.
3. Add the whole pint of sulfuric/battery acid. Agitate some more!
4. Add about 1 TBL of the "New Copper Brightener Part B". Agitate!
5. If you have a 3 gallon jug and there is room, top it off with more distilled water. Don't do this if you have the 5 gal. jug as the extra room is for easier agitating and the solution will become too weak.
You are done with the solution. Pour what you need into your electroforming bath container. When you are done (hours, days, weeks, whatever) run it through a filter back into the jug.
It is also handy to put a cheap aquarium pump into the solution while you are electroforming.
Follow your electroforming instructions using "Copper Conductive Paint" on non-metallic objects (also order from www.caswellplating.com ). Porous objects need to be lacquered first. Glass does not. Copper conductive paint and copper wire provides the conduit for the current. Paint your design on the object, bead etc and attach your copper wire from the negative (cathode) somewhere to the paint.
This is not intended to be a complete electroforming tutorial, which can be extensive...just to give you the recipe. Electroforming instructions can be found online. http://www.katefowle.com/pages/tips.php
I will post a photo of some items that I have done using this solution.
__________________
Carol
StewArt Glass and Gem
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-01, 11:11pm
|
|
Member
|
|
Join Date: Nov 09, 2011
Location: Fallon, Nevada
Posts: 84
|
|
A couple of additional notes on above recipe: As the solution evaporates with use, add small amounts of distilled water.
As the brightening effect seems to be wearing off add small amounts of the Copper Brightener Part B...about 1 tsp (if you are making the whole 3 gallons).
I use a big bath and put several items in at a time. I use a Rubbermaid or Sterlite deep plastic tub with lid.
Questions maybe pm'd to me or asked here!!
__________________
Carol
StewArt Glass and Gem
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-02, 9:25am
|
|
Senior Member
|
|
Join Date: Jul 24, 2005
Posts: 256
|
|
Thank you. I will give it a try next time I need more solution. Do you think it will be okay to add what I make to the existing batch (purchased) I have now?
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-02, 10:16am
|
|
Member
|
|
Join Date: Nov 09, 2011
Location: Fallon, Nevada
Posts: 84
|
|
I don't see why not. Even tho it's got the acid in it, it isn't really caustic. The stuff you have is probably close to the same. To be sure, do it outside and wear a mask, and do just a little bit at a time.
__________________
Carol
StewArt Glass and Gem
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-02, 10:51am
|
|
Still makin' flowers...
|
|
Join Date: Feb 26, 2006
Location: Oregon...
Posts: 2,388
|
|
OMG. Awesome. Thank you.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
* To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. --NEW and Updated Beading Tutorials for all levels
* To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. -- Sign up for my To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. !
|
2014-12-02, 11:32am
|
|
Member
|
|
Join Date: Nov 09, 2011
Location: Fallon, Nevada
Posts: 84
|
|
A photo of some shells I did some time ago!
__________________
Carol
StewArt Glass and Gem
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-03, 12:11am
|
|
Senior Member
|
|
Join Date: Feb 13, 2011
Location: Oregon
Posts: 626
|
|
I mix my own solution and have not added the brightener. Just the crystals and the acid. I haven't had much time to play with my recipe and the only difference I noticed between the commercially mixed product and my recipe was that the electroform was laid down thicker than with the commercial version of solution. Being that the thickness of the copper is a function of the current, I need to do more experiments to determine if my solution is conducting the current better or if the diff of .5 vs .7 really caused the heavier deposit.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
All my children have paws To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. Proud Member of "YOU PEOPLE" 9.13.11 To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-03, 1:18am
|
|
Still makin' flowers...
|
|
Join Date: Feb 26, 2006
Location: Oregon...
Posts: 2,388
|
|
I love this thread. I'm going to go delete the one in the Garage Sale section now...
-------
edited to add... @Patti
I bought this one: http://www.amazon.com/gp/product/B00...?ie=UTF8&psc=1
Haven't had a chance to try it out yet, though.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
* To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. --NEW and Updated Beading Tutorials for all levels
* To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. -- Sign up for my To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. !
|
2014-12-03, 3:17pm
|
|
Member
|
|
Join Date: Nov 09, 2011
Location: Fallon, Nevada
Posts: 84
|
|
You know...you could be right on the brightener not being really needed. I have a eurotool bench polisher and that will bring up a nice shine too. If you can get the other ingredients readily ( should be no problem) then try it before you spend $$ on the brightener and waiting for it to arrive. The conductive paint is essential tho. My bottle of brightener will last me 3 lifetimes...i have a problem in not buying small amounts. If it wasn't a shipping problem (hazardous) i could send you all some.
__________________
Carol
StewArt Glass and Gem
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-03, 3:19pm
|
|
Member
|
|
Join Date: Nov 09, 2011
Location: Fallon, Nevada
Posts: 84
|
|
Hannah...the rectifier is almost identical to mine. It should work well for you.
__________________
Carol
StewArt Glass and Gem
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-03, 7:03pm
|
|
Senior Member
|
|
Join Date: Mar 09, 2009
Location: Medford Oregon
Posts: 900
|
|
http://www.mastechpowersupply.com/dc...prod_64.htmlas
Has anyone been able to say whether this is the same machine as the rectifier you are using for electroforming?
__________________
Dawn To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-04, 9:35am
|
|
Senior Member
|
|
Join Date: Mar 09, 2009
Location: Medford Oregon
Posts: 900
|
|
Bump
__________________
Dawn To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-04, 3:04pm
|
|
Member
|
|
Join Date: Nov 09, 2011
Location: Fallon, Nevada
Posts: 84
|
|
I asked the dh who was an electrician and he said it should be fine. BTW...mine is a HY1505. Good price!
__________________
Carol
StewArt Glass and Gem
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-05, 7:49pm
|
|
Senior Member
|
|
Join Date: Feb 13, 2011
Location: Oregon
Posts: 626
|
|
Yes Dawn-that would be what you need. A LOT cheaper than the Rio one.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
All my children have paws To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. Proud Member of "YOU PEOPLE" 9.13.11 To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-05, 8:57pm
|
|
Senior Member
|
|
Join Date: Mar 09, 2009
Location: Medford Oregon
Posts: 900
|
|
Yay! I am going to get one
We will have to set a play date Marie.
__________________
Dawn To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-09, 11:54pm
|
|
Senior Member
|
|
Join Date: Feb 13, 2011
Location: Oregon
Posts: 626
|
|
That we do!
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
All my children have paws To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. Proud Member of "YOU PEOPLE" 9.13.11 To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-18, 6:38am
|
Senior Member
|
|
Join Date: Jan 22, 2012
Location: Florida
Posts: 591
|
|
Wow, thank you..
__________________
Life without art would be BORING!
ArtbyCherri.com
|
2014-12-18, 10:36am
|
|
Still makin' flowers...
|
|
Join Date: Feb 26, 2006
Location: Oregon...
Posts: 2,388
|
|
Did it... The recipe works perfectly.
The copper conductive paint I bought from Rio Grande, however, was decidedly NON CONDUCTIVE. What a big waste of money. I should have gone with the other stuff, but was trying to save time. And they still haven't refunded me, even though they already knew their product was a dud.
I have the other stuff being delivered today, but MEANWHILE, if you take latex paint (white) and add enough graphite powder to it to make it medium grey (Shawn makes graphite tools, so we always have plenty of that), you get really conductive paint.
__________________
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
* To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. --NEW and Updated Beading Tutorials for all levels
* To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. -- Sign up for my To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. !
|
2014-12-18, 11:29pm
|
|
Member
|
|
Join Date: Nov 09, 2011
Location: Fallon, Nevada
Posts: 84
|
|
Hey...that is good to know on the conductive paint!!! I have bottle of graphite powder some place in the shop and it probably was pretty cheap. I will have to try that!! Thanks, Hannah for that little bit of info!!!
__________________
Carol
StewArt Glass and Gem
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-26, 7:05am
|
Senior Member
|
|
Join Date: Jan 22, 2012
Location: Florida
Posts: 591
|
|
Wanted to again say thank you for this post.. I am anxious to try it out. I have been looking for some time. Now to get the machine itself and I will be all set. Thank you.
__________________
Life without art would be BORING!
ArtbyCherri.com
|
2014-12-26, 2:33pm
|
|
Tacki
|
|
Join Date: Oct 26, 2008
Location: DFW, TX
Posts: 1,543
|
|
Quote:
Originally Posted by Birdsonawire
|
I'm starting to get everything together for a kit. I'm totally green on this so bear with me... is this in place of a rectifier?
|
2014-12-28, 9:10pm
|
|
Member
|
|
Join Date: Nov 09, 2011
Location: Fallon, Nevada
Posts: 84
|
|
Yes...to answer your question. I use a 1505 and this is a 1503. Mine doesn't have a ground connection, so i would just ignore the one on this machine. Hook up red/positive/anode and black/negative/cathode. Or you can go with the 1803 which is like Hannah's which is 3 amps and 18 volts...slightly more voltage.
__________________
Carol
StewArt Glass and Gem
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2014-12-29, 10:17am
|
|
Tacki
|
|
Join Date: Oct 26, 2008
Location: DFW, TX
Posts: 1,543
|
|
Whoa, they want $20 for shipping? That seems excessive
|
2014-12-29, 10:22am
|
|
Tacki
|
|
Join Date: Oct 26, 2008
Location: DFW, TX
Posts: 1,543
|
|
I found it on amazon with $16.49 shipping, but then I found this and it's free shipping if you have prime: http://www.amazon.com/gp/product/B00...=AMH4W1K8OCGMX so it's actually the same price as the one listed from mastech but with more voltage... so... clicking purchase now Thanks!
|
2014-12-30, 11:05am
|
|
Member
|
|
Join Date: Nov 09, 2011
Location: Fallon, Nevada
Posts: 84
|
|
Traci...that's a great one! Same as Hannah's. Good luck with the electroforming!!!
__________________
Carol
StewArt Glass and Gem
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2015-01-04, 1:47pm
|
|
Senior Member
|
|
Join Date: Mar 16, 2007
Location: Polson, Montana
Posts: 119
|
|
This is great! Thanks for sharing Carol, I was just thinking about getting back to do some electroforming.
|
2015-01-10, 8:13am
|
Senior Member
|
|
Join Date: Jan 22, 2012
Location: Florida
Posts: 591
|
|
so we don't need the tinning solution? I am getting ready to order the supplies from caswell. thank you again.
Oh and can the copper paint be applied with a brush instead of an airbrush.
__________________
Life without art would be BORING!
ArtbyCherri.com
|
2015-01-10, 8:46pm
|
|
Member
|
|
Join Date: Nov 09, 2011
Location: Fallon, Nevada
Posts: 84
|
|
Yes to the brush. The copper conductive paint i got from Caswell is silver in color...at least mine was. Works fine. Thin with distilled water if needed. If you can get a small bottle of brightner, i would get it since you are ordering anyway.
__________________
Carol
StewArt Glass and Gem
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2015-01-11, 8:30am
|
|
Practicing perfect
|
|
Join Date: Oct 12, 2007
Location: Fullerton, CA
Posts: 2,050
|
|
Carol, thank you for sharing.
Great thread.
__________________
Inez
In the hopes of reaching the moon men fail to see the flowers that blossom at their feet - Albert Schweitzer
To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts.
|
2015-01-31, 7:56pm
|
Naysayer
|
|
Join Date: Sep 22, 2009
Posts: 1,204
|
|
Thanks for this
I've never done this, I see some kits have a fish tank heater, any need for that? It is very cold in my garage where I will be doing this.
And Traci, did yours come with leads? They never show them with leads, if they do not, what kind do I buy? I see so many and I get confuzzled.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 11:24am.
|